15 Reasons You Shouldnt Ignore Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs
Have your uPVC window or door mechanism deteriorated? Perhaps the handles on your uPVC windows or doors aren't aligned correctly or are difficult to use.
It's important that your double glazed doors operate smoothly, otherwise you'll lose energy and increase the likelihood of burglary. Owen the Locksmith can repair your door lock at a reasonable price.
Snapped Key
If a key breaks in a lock, it can be incredibly annoying. It also poses an issue for security, since the door may not be locked and leave you vulnerable to intruders. There are a few easy fixes you can try to repair the issue and get your door working again.
Remember to remain calm. If you panic and start playing around with your keys you may end up pushing the damaged piece of the key deeper into the lock, which could make the situation much worse.
Next spray WD-40 or another penetrating oil into the lock to help the broken piece slip out more easily. You can also use a screwdriver to break any pieces that are stuck. If you're lucky enough to have a small piece of the key left hanging out and you want to remove it, use a paperclip or some other thin metal object to grab it and pull it out. Both methods work, but be careful not to push the broken key further into the keyway.
Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades can also work well for this. If you do not have any of these available, you can use needle-nose pliers to bend and create hooks. Finally, a pair of tweezers is a good way to grasp and remove the remaining bit of the broken key.
If you can't get the broken piece of the key out, try using a lock de-icer. It's available in many hardware stores and works by freezing any moisture that may be present in the lock.
If none of these methods are working then it's probably the time to contact locksmith. Fitlocks specialists are able to quickly fix problems with uPVC door mechanisms and locks that have snapped keys as well as broken handles. They can also reconfigure the double glazing door mechanisms so that they are more easy to operate. You can book an appointment online for a double-glazing repair or call us to discuss your needs.
Broken Cylinder
A broken cylinder is an extremely risky security issue. A professional locksmith can easily fix the cylinder. To fix the cylinder, locksmiths will need to tap it. They can do this using the hammer or any other tool, but the best method is to make use of a long match or piece of wire. Then, put the match's end or wire near the keyway. The locksmith can then hit the lock to crack it. This is much better than using a hammer that can cause damage to the lock.
The most frequent cause for cylinder head cracks is overheating. This can occur when the cylinder head and block are made from different metals like cast-iron and aluminium. When the different metals heat up and cool down at different rates, it may cause localised hotspots that expand faster than the rest of the cylinder head, leading to cracks.
Another possible cause for cylinder cracks is corrosion. If the cylinder head as well as cylinder block are not maintained properly, this could result in corrosion or rust and cause them to expand at a greater rates than they should. This could lead to cracks over time.
If your uPVC window or door lock is brittle and requires a lot of pressure to turn, it could be due to a variety reasons. A faulty locking mechanism, misalignment, or an old handle are the most common reasons for this issue.
It is a quick and affordable fix that the majority of homeowners with double glazing can perform. A professional locksmith can usually fix this problem within one hour of arriving at your property. Based on your requirements they will be able to replace the locking mechanism, change the window handles, or change the gearboxes. A locksmith with experience will always be able to advise you on the most cost-effective solutions for your home. They can also suggest upgrades to the highest-security 3 Star Euro cylinders, TS007, that will provide an extra layer of protection against burglars. It's a small price to get the peace of mind that comes from knowing that your uPVC door is secure.
Broken Handle
Window handle locks have complex mechanisms that wear out with age and use, so it's no surprise they occasionally break. It can be difficult to determine the reason for the problem and then fix it properly.
If the issue is in the internal locking mechanism or the latch, repairing your broken handle will improve your uPVC double glazing door's security and help you stop draughts. It is costly to replace or repair your handle if it is not done correctly and can also damage the frame and the lock of your door.
Screwdriver When the window is open and the screw loose, loosen the handle. The screw should be on the inside of the backplate, usually covered by an eye-catching cap to conceal it to enhance the appearance. Be sure not to damage any of the internal components within the handle, like the plates or levers on the opposite side of the spindle. Ideally, keep these in the same order so that you can re-install them when needed.
Then, turn the handle so it's at 90 degrees to the window frame. Finally, loosen the screw at the back of the handle which holds it to the internal spindle with a second screwdriver. Once the screw is loose, pull the handle out and take the broken spindle out. Replace it with a new one, making sure that it is the same length as the previous one (you can typically find these on the internet or in hardware stores) and screw it securely into place. Be careful not to overtighten as this could damage the handle or the window frame.
Close the handle and try it. It should work smoothly and you'll be able open your window once more.
While you're working on the handle, be sure to check your uPVC windows are shut properly. If they don't cause draughts and damp in your home, as and also affecting the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure that they close correctly.
Broken Spindle
It is more typical for the spindle to break than the handle. This is most common in uPVC tilt and turn windows. These kinds of windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is connected to a centre rod that in turn activates cams that look like mushrooms, they locks are inserted into the window frame. If the dead latch mechanism is not able to open after the handle is turned, it's likely the spindle has been damaged. This could be a problem that is frustrating.
Fortunately, there are steps that can be taken to fix this problem. A good locksmith can quickly and effectively fix the issue. A reputable locksmith will be able to disassemble the window's handle using a tool that removes the wheel portion where the spindle is located. This is done without damage to the handle or the window frame.
After removing the wheel, the technician can inspect the spindle and identify what caused it to break. This involves disassembling the spindle, and then examining each component, noting any damage or excessive wear. The process is carried out in a clean room by highly skilled technicians.
Then, clean Read More In this article damaged spindle. This will remove any dirt or debris which may be obstructing it from operating normally. After this, the spindle could be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is comparable in size to the original. He will then make holes in the same way into both pieces. This will ensure that the spindle fits perfectly with the handle.
If the spindle is damaged and cannot be repaired it may need to be replaced entirely. Home centres sell generic substitutes however if your window style is rare you'll have to speak with an expert in cabinet making or woodworking who can recreate the exact part. Once the spindle has been installed, it is fixed to the handle. The screw holes on the handle with the existing screws in the frame. Once the new handle is firmly installed, you are now ready to operate your uPVC window.