15 Reasons You Shouldnt Ignore Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs
Are you experiencing issues with your uPVC window or door mechanism broken? Perhaps the window or door handles aren't aligned properly or are hard to use.
You will lose energy if your double-glazed doors don't function properly. This increases the likelihood of burglaries. Owen the Locksmith can fix your door lock at a reasonable cost.
Snapped Key
It can be quite frustrating when a key snaps inside a lock. It could also be a security issue in that it can make you vulnerable to an intruder if the door does not lock. There are fortunately quick fixes that you can use to solve the issue and get your door working properly once more.
Be calm. If you panic, you could end up pushing the damaged key further into the lock.
Spray WD-40 or another penetrating lubricant into the lock. This will allow the broken piece be removed more easily. You can also make use of a screwdriver to break pieces that could be hindering the flow. If you have a piece of the key that is stuck, grab it with a paperclip or another thin metal object and pull it. Both methods work, but be careful not to push the damaged key further into the keyway.
Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades also work well for this. If you don't happen to have any of these then you can bend a hook with needle-nosed pliers. Also, a pair tweezers can be used to grasp and remove the remaining bit of the broken key.
If you are unable remove the broken piece of key then you can use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present in the lock.
If none of these tricks seem to be helping then it's probably the time to contact locksmith. Fitlocks specialists are able to quickly resolve issues with uPVC door locks and mechanisms that have snapped keys as well as broken handles. They can also alter your double glazing door mechanisms to make them easier to operate. Book a [1] double glazing repair through us online or give us a call to discuss your requirements.
Broken Cylinder
A damaged cylinder poses a serious security threat. It's fortunately a simple repair for professional locksmiths to complete. To fix the cylinder, locksmiths will need to tap it. They can do this with an hammer or another tools, but the most effective method is to make use of a long match or piece of wire. The match or wire's end in the keyway. The locksmith will then strike the lock in order to break it. This is better than using the hammer, which could cause damage to the lock.
The most frequent cause of cracks in the cylinder head is overheating. This can happen when the block and the cylinder head are made of different metals like cast-iron and aluminium. Different metals will be heated and cool at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.
Corrosion can be a cause of fractures in cylinders. If the cylinder block and head are not maintained correctly they could be corroded or rust and cause them to expand more than anticipated. This can lead to cracks in the future.
If your uPVC window lock or door is brittle or requires a lot of pressure to turn, it can be the result of many things. A malfunctioning locking mechanism, misalignment or a worn handle are common reasons for this issue.
It is a quick and cost-effective fix that a majority of homeowners with double glazing can perform. A professional locksmith will typically be able solve this issue within a matter of hours of arriving at your home. Depending on the needs of your home, they can replace the locking mechanism, change the window handles, and also change the gearboxes. A locksmith with experience will always be able to advise you on the most cost-effective options for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders which give you an extra security layer from burglars. It's a small price to pay for the peace-of-mind that comes from knowing that your uPVC door is secured.
Broken Handle
It's not a surprise that window handle locks may break. They have complex mechanisms that wear out over time. If yours fails, it can be difficult to identify the cause of the issue and make sure that you repair it correctly.
Repairing your damaged handle, whether it's the internal latch or locking mechanism can increase the security of your uPVC door and stop draughts. It is costly to replace or repair the handle in a way that isn't done correctly. It can also damage the frame and lock of your door.
With the window open, loosen the screw holding the handle using a screwdriver. This should be located on the inside face of the back plate, normally covered by an attractive cover for the screw for aesthetic reasons. Be careful not to lose any of the internal parts within the handle, for example the levers or plates on the opposite side of the spindle. Ideally, keep them in the same place so you can re-install them in the event of a need.
Then, turn the handle so it's at 90 degrees to the window frame and loosen the screw at the back of the handle which holds it to the internal spindle by using another screwdriver. Once the screw is removed, you should be capable of pulling the handle away and pull off the damaged spindle. Replace it with a new spindle, making sure it's the same length (you can buy them on the internet or at hardware stores). Securely screw it in the frame. Do not overtighten the screw as this could cause damage to the handle and window frame.
Check that the new handle is correctly fitted Close the window and test the handle. The hope is that it will function smoothly and you'll be able unlock your window.
While you're working on the handle, be sure to ensure that your uPVC windows are closing properly. If they don't close correctly, you could encounter draughts or damp in your home. It could also affect the energy efficiency of your home. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they shut correctly.
Broken Spindle
It is usually the case that the spindle within the handle breaks, rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is attached to a central rod which in turn activates cams that resemble mushrooms, which locks are inserted into the window frame. If the dead latch mechanism does not open after the handle has been turned, it's likely the spindle has been damaged. This can be a frustrating issue.
Fortunately, there are ways to rectify this issue. A reputable locksmith can swiftly and efficiently fix this problem. A good locksmith will be able disassemble the window's handle using a tool to take out the wheel portion where the spindle is located. This is done without damaging the handle or causing other damage to the frame of the window.
Once the wheel is removed the technician can then examine the spindle to determine what caused it to break. This involves breaking the spindle into its individual components and carefully observing their general condition as in addition to any specific areas of damage or excessive wear. This process is usually performed by technicians in a clean environment.
Next, clean the damaged spindle. This will remove any debris or dirt that could be hindering it from operating normally. The spindle may be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is the same size to the original. He will then drill matching holes into both pieces. This will ensure that the new spindle has an exact fit with the handle.
If the damaged spindle is beyond repair, it may be required to replace it completely. Home centres sell generic replacements but if the design of your window is unique then it will be necessary to find a woodworker or cabinet maker who can make the exact component for you. Once the new spindle is installed, it can be attached to the handle by line up the holes for screws in the handle with the frame's existing screws. Once the handle is firmly set, you are able to operate your uPVC windows.